|
Monel Products
Our monel products is available in a variety of shapes and sizes, both pre-cut and custom forged. This product is available in form of monel pipes tubes, fittings, sheets, plates, coils, round bars, flanges and fasteners etc.
Monel 400 (UNS No. NO. 4400)
Monel 400 is a nickel-copper alloy (about 67% Ni – 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold working. This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength. A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions. This nickel alloy is particularly resistant to hydrochloric and hydrofluoric acids when they are de-aerated. As would be expected from its high copper content, alloy 400 is rapidly attacked by nitric acid and ammonia systems.
Monel 400 has great mechanical properties at subzero temperatures, can be used in temperatures up to 1000° F, and its melting point is 2370-2460° F. However, alloy 400 is low in strength in the annealed condition so, a variety of tempers may be used to increase the strength.
Monel 500 (UNS No. N0. 5500)
Monel K-500 is a precipitation-hardenable nickel-copper alloy that combines the excellent corrosion resistance characteristic of Monel 400 with the added advantage of greater strength and hardness. These amplified properties, strength and hardness, are obtained by adding aluminum and titanium to the nickel-copper base and by a thermal processing used to effect precipitation, typically called age hardening or aging. When in the age-hardened condition, Monel K-500 has a greater tendency toward stress-corrosion cracking in some environments than Monel 400. Alloy K-500 has approximately three times the yield strength and double the tensile strength when compared with alloy 400. Plus, it can be further strengthened by cold working prior to precipitation hardening. The strength of this nickel steel alloy is maintained to 1200° F but stays ductile and tough down to temperatures of 400° F. Its melting range is 2400-2460° F. |
|
|
Monel Pipes
Monel pipes are known for their excellent performance. It can be used in the soft drink industry because it's harmless to human body. It has high resistance to temperature, so that it can be used for transportation of hot water, chemical and gas.
RANGE : 15 NB UP TO 600 NB IN SCH 5S , 10S ,10, 20 , 40S , 40 , STD , 60 , 80S , 80 , XS , 100 , 120 , 140 , 160 & XXS
TYPES: Seamless ERW welded fabricated
Grades as under:- Monel 400 (UNS No. N04400), Monel 500 (UNS No. N05500)
Size available: ½" NB to 24 "NB in SCH 5S , 10S ,10, 20 , 40S , 40 , STD , 60 , 80S , 80 , XS , 100 , 120 , 140 , 160 & XXS available in type SEAMLESS / ERW / WELDED/efsw
|
 |
Monel Tubes
Monel tubes are available in following types range and grades.
Types: • Seamless • ERW • Welded in Round & Square
Range: 6.35 mm OD up to 254 mm OD in 0.6 to 20 mm thick
Grades as under:- Monel 400 (UNS No. N04400) Monel 500 (UNS No. N05500)
Size Available: 6.35 mm OD up to 254 mm OD in 0.6 TO 20 mm thickness
TYPE :SEAMLESS / ERW / WELDED |
 |
Monel Sheets & Plates
Our gamut of monel sheet ,plates and coils is available in different sizes with thickness varying from 0. 1 mm to 150 mm.
Range :
0. 5 mm to 200 mm thick in 1000 mm to 2500 mm width & 2500 mm to 12500 mm length available with nace mr 01-75
Grades as under:- monel 400 (uns no. N04400), monel 500 (uns no. N05500)
Size Available:
0.1 mm thickness to 150 mm thickness.
1000 mm x 2000 mm
1220 mm x 2440 mm (4' x 8')
1220 mm x 4880 mm
1250 mm x 2500 mm
1500 mm x 3000 To 6300 mm
2000 mm x 2000 To 10000 mm and
As per requirement
Type: straight and in coil form
|
 |
Monel Rods / Bars
Our striking range of monel rod /bars is available in different forms and sizes. All our products are offered as per the international standards. With the assistance of our experts and professionals.
Range :100 mm dia to 500 mm dia in 100 mm to 6000 mm length
Grades as under:- monel 400 (uns no. N04400), monel 500 (uns no. N05500)
Size Available:1 mm dia to 200 mm dia |
 |
Monel Fittings
We are offering a complete range of monel fittings which is available as per the following specifications:-
Types of monel fittings:
Elbow 90 deg, elbow 45 deg, cross, tee, coupling, half coupling & cap
Range :
15 nb to 100 nb in 3000 lbs, 6000 lbs, 9000 lbs available with nace mr 01-75
Grades as under:-
Monel 400 (uns no. N04400)
Monel 500 (uns no. N05500)
Size Available:
½" NB to 24 "NB in SCH 5S , 10S ,10, 20 , 40S , 40 , STD , 60 , 80S , 80 , XS , 100 , 120 , 140 , 160 & XXS
Such as 90° ELBOW ( LONG RADIUS / SHORT RADIUS ), EQUAL TEE, 45° ELBOW ( LONG RADIUS / SHORT RADIUS ), REDUCING TEE, ROUND CAP, CONCENTRIC REDUCER, ECCENTRIC REDUCER, STUB END (short/long), coupling (half/full) -
Type: SEAMLESS / ERW / WELDED.
|
 |
Monel Flanges
We are catering a qualitative range of monel flanges which is available in various forms and standards. These flanges are available in different sizes. As per the international standards, we offer the gamut which is in high in demands in domestic and international markets.
Specifications:
- Standards: ASTM / ASME SB 564
- Grades: Monel 400 (UNS No. N04400), Monel 500 (UNS No. N05500)
Size:
1/8" NB TO 48"NB.
STANDARD :
ASTM
BS
DIN
IS
Forms of flanges:
- Socket Weld
- Weld Neck
- Slip on
- Long Weld Neck
- Blind
- Reducing
- Lapped
- Spectacle
- Screwed
- Ring Joint
Size Available:½" NB to 24 "NB in Weld neck, slip on , Socket Weld, Blind, lap joint, raised face , Flat face, threaded flanges, orifice flanges in class of 150, 300, 600, 900, 1500, 2500 |
 |
|
|
|
|
![[Most Recent Quotes from www.kitco.com]](images/nickel-d.gif)